-
What This Checklist Covers (and Who It's For)
-
The 7-Step Checklist
-
Step 1: Confirm pitch and pin count against the datasheet, not the product photo
-
Step 2: Match the crimper to the terminal before ordering the terminals
-
Step 3: Verify plating spec—Sn vs. SnPb vs. Au flash
-
Step 4: Check housing-to-terminal compatibility on the mating half
-
Step 5: Run the pull test and log the number
-
Step 6: Check batch-to-batch consistency, not just the sample
-
Step 7: Get the CoC and datasheet revision in writing
-
Step 1: Confirm pitch and pin count against the datasheet, not the product photo
-
Notes, Common Errors, and One More Thing
What This Checklist Covers (and Who It's For)
I run quality and brand compliance for an electronics assembly shop—most of our volume is JST connector work. Every connector that comes through our dock, whether it's a 50-piece sample or a 5,000-unit production run, goes through the same 7-step pre-order verification. Takes about 40 minutes per SKU. Worth every minute.
This list is for procurement engineers, small shops buying their first samples, and anyone tired of finding a plating mismatch after the boxes are already on the shelf. Use it when you're onboarding a new supplier, when the SKU is going into a customer-facing product, or when you've had a field return you can't explain. Small orders get the same checks as big ones—a $200 trial run still gets a proper look (more on that at the end).
Quick definition first, since it's the question behind a lot of search traffic: a connector is an electromechanical interface that joins two conductors—typically a housing, a terminal (the metal contact), and a mating half. "JST" is the brand name; the letters after it (PH, SH, XH, VH, SUR) designate the series, and the series determines the pitch.
The 7-Step Checklist
Step 1: Confirm pitch and pin count against the datasheet, not the product photo
Micro JST 2-pin connectors are one of our highest-volume buys, and also where I see the most mismatches. "Micro" is a marketing word—it can mean SH (1.0 mm pitch), PH (2.0 mm), or GH (1.25 mm). If a drawing says "micro" and nothing else, stop. Get the series letter and pin count in writing (like "PH series, 2-pin, 2.0 mm pitch").
I assumed "same specifications" meant identical results across vendors. Didn't verify. Turned out each supplier had a slightly different interpretation of "2-pin micro." One quote came back as 2.0 mm PH; another was 1.25 mm GH. Different footprints entirely. Learned never to assume the photo represents the actual part after that.
Step 2: Match the crimper to the terminal before ordering the terminals
This is the one most people skip, and the one that causes the most rework. JST terminals are rated for specific crimp tools—either JST's own hand crimpers or a calibrated applicator. If you're using a generic crimper, verify the crimp profile against IEC 60352-2 (the standard for solderless crimped connections). A crimper that "works" but deforms the terminal will pass visual inspection and fail at temperature cycling—typically 6-12 months after installation, when nobody remembers the batch.
We learned this the hard way. A batch of 3,000 terminals from a distributor out of De Soto, KS looked fine going out the door. Twelve weeks later we had field returns. The crimp barrel had been collapsed instead of formed. The fix meant re-terminating every harness (ugh).
Step 3: Verify plating spec—Sn vs. SnPb vs. Au flash
Two connectors can be functionally identical and still fail incoming inspection purely on plating. Tin (Sn) is standard for most JST lines. But if your application sees high sulfur or humidity, you want gold (Au) flash; if it's aerospace or medical, you may be locked to a specific alloy. Do not accept "same as before"—that's a fuzzy answer you can't audit against. Ask for the material declaration or CoC, dated within the last 12 months. If they push back on the date, that itself is your answer.
Step 4: Check housing-to-terminal compatibility on the mating half
JST VH 3-pin is a good example. The VH series has a 3.96 mm pitch, a locking ramp, and a specific crimp style. I've seen VH-style housings from third parties that accept the JST terminal but not the retainer—so it installs, looks right, and then fails a pull test. Confirm the retainer clips engage and the housing locks fully. If you can't demonstrate it on a sample, don't approve it.
Step 5: Run the pull test and log the number
Per IPC/WHMA-A-620, wire-to-terminal pull strength should be documented per wire gauge and strand count. For 24 AWG in a PH-series terminal, we target roughly 15 N minimum; a loose terminal can pass visual and fail at 4 N. No pull test, no approval (for me, non-negotiable). Keep the number. When the same SKU comes back next quarter, you'll want to compare—pulling more than 10% lower than the last batch is a signal the die set has worn.
Step 6: Check batch-to-batch consistency, not just the sample
Here's where the data gap bites me. I don't have hard data on industry-wide batch variance rates, but based on our last four years of incoming inspection, my sense is that around 8-12% of first deliveries show at least one spec drift—usually pitch or plating, rarely housing color. If I only check the first sample, I'm approving a batch I haven't actually seen. Pull 3-5 units from across the box and check the extremes (first, middle, last from the reel). The extremes are where reels get spliced or a cut-off lot sneaks in.
Step 7: Get the CoC and datasheet revision in writing
A Certificate of Conformance plus the specific datasheet revision (not just "JST compatible") is what protects you when a customer asks. We require it on every incoming batch now. The last time we skipped it, the customer asked for revision evidence six months later and we couldn't produce it (missed deadline). Now every contract includes the datasheet revision requirement. Every single one. (Note to self: add the revision number to the receiving form—kept forgetting that for two months.)
Notes, Common Errors, and One More Thing
A few items I always flag for new team members:
- The photo trap. Product photos often show the wrong pitch. Always verify against the engineering drawing.
- "Our version is compatible." Compatibility without a tested pull value and a retainer check isn't compatibility—it's a guess. Treat it as a red flag.
- The crimper audit. Even with the right tool, check the die set for wear. Wear changes the barrel geometry, and the change doesn't show up in the finished crimp until failure. (Note to self: monthly die log.)
- Small orders count. When I was starting out, the vendors who took my $200 sample orders seriously are the ones I still use for $20,000 production orders. Small doesn't mean unimportant—it means potential. A 50-piece micro JST 2-pin order that shows up with the right pitch, plating, and packaging is a signal. So is the opposite.
None of this is exotic. It's the boring work that separates a batch that clears inspection from a batch that comes back six months later. Run the checks, log the numbers, keep the CoC.
Pricing and lead-time figures are illustrative. Verify current pricing and datasheet revisions with JST-authorized distributors at the time of order.